Boring > Point to Point

Weeke Feed through Bore and route BHX 500

MA ID: PTP-11087
Price: $98,000.00 -or- as low as $1,980.58/mo.*
General Location: South East

Point to Point

Boring - Feed Through

Manufacturer: Weeke
Model: BHX 500
Year of Manufacture: 2007
Condition: Good
Electric 480 volt, 60 cycle, 3 phase


Workpiece Dimensions          

Minimum work piece length: 200 mm                                            

Maximum work piece length: 2500 mm                                                                 

Minimum work piece width: 70 mm                                                                              

Maximum work piece width: 1000 mm                                                                          

Minimum work piece thickness: 4 mm                                                                           

Maximum work piece thickness: 80 mm                                                                         

Maximum work piece stacking: 2 pieces                                                                          

Automatic Workpiece Clamping Units                        

Two (2) work piece clamping devices with integrated stop system feeds parts in and out of the machine without disturbing edges via TBO-System(Top-Bottom Open-System).

- Separate adjustment of the clamping devices via rack and pinion gear in X-direction.               

- Digital AC servomotors.                                                                                                 

- The position of the clamping devices at the work piece is program-controlled                  

- Automatic measuring of the work piece thickness is integrated in the clamping                        

Upper Processing Support                                   

- Rigid aluminum cast construction.                                                                               

- Integrated threefold divided table with selectable air cushion.                                            

- Lateral stop system.                                                                                                        

- Adjustment of the axes in Y- and Z-direction.                                                               

- Ball bearing spindle (Z-direction) and rack and pinion gear (Y-direction).                               

- Digital AC servomotors.                                                                                                 

- Suitable for fitting of various configurations.                                                                  

Lower Processing Support                                   

- Rigid aluminum cast construction.                                                                                 

- Integrated threefold divided pressure beam with selectable air cushion.                                

- Adjustment of the axes in Y- and Z-direction.                                                               

- Ball bearing spindle (Z-direction) and rack and pinion gear (Y-direction).                               

- Digital AC servomotors.                                                                                                 

- Suitable for fitting of various configurations.                                                                  

Workpiece Feeding Area                                       

- Smooth-Pressure System Air cushion table in rigid frame construction.                               

- Surface from phenolic board with tracer valve.                                                               

Two (2) Vertical Boring Blocks 32 Spindles                         

Vertical drilling block each in the upper and lower processing support with 32 drilling spindles each (separately activated with infinitely program controlled

high speed range).  Spindle clamping to achieve the drilling depth safely.                              

Stroke: Z-direction: 60 mm                                                                                                

Drilling depth: maximum 38 mm                                                                                           

Direction of rotation: right hand/left hand                                                                       

Speed: 1500 - 7500 1/min                                                                                                  


Drive: 2 x 2.7 kW                                                                                                             

Shaft diameter: 10 mm                                                                                                      

Total length of drill: 70 mm                                                                                          

Drilling diameter: maximum 35 mm                                                                              

Distance between spindles: 32 mm                                                                                

Type of spindle: individually selectable                                                                            

Two (2) Grooving Saws X-Y 90°                            

Grooving saw aggregate each in the upper and lower processing support for processing in X-Y direction, 90 degrees swiveling.                                                                                                                                                             

Cutting depth: 30 mm                                                                                                  

Cross section: maximum 70 mm2                                                                                  

Rotation: 1500 - 7500 1/min                                                                                              


Tool diameter: 125 mm                                                                                                     

Blade width: maximum 5 mm                                                                                                 

Two (2) Vertical Router Motors (ETP-8 HP)                        

Tool holder: for shaft diameter 25 mm                                                                           

Tool diameter: maximum 50 mm                                                                                   

Visible tool length: minimum 65 mm / maximum 100 mm                                                    

Tool weight: maximum 2.5 kg                                                                                           

Tool intake: manually by means of fast hydro clamping system ETP 25                                 

Direction of rotation: right hand / left hand                                                                     

Speed: stepless, 6000 - 18000 1/min                                                                                


Drive: frequency controlled                                                                                                    


Maximum capacity at the tool: up to 5 / 6 kW in continuous and intermittent operation                   

Workpiece Removal Area                                                                                                 

- Cross belt conveyor in rigid frame construction.                                                              

- Eight (8) transport belts, frequency-controlled drive.                                                      

- Eight (8) electro-pneumatic controlled disengaging device with integrated universal rollers.          

Electronic Hardware                                                                                                         

- Control including drive modules.                                                                                      

- Intelligent control system, while the CNC-Control steers the processes new data                    

can be independently inserted at the PC.                                                                         

- PC (personal computer) with operating surface.                                                             

- Intel Pentium compatible.                                                                                                

- English operating system Windows XP embedded.                                                                

- 15 inch graphic monitor (TFT).                                                                                        

- 512 Mbyte RAM memory.                                                                                              

- Minimum 40 Gbyte hard disc drive (different partitions).                                                    

- 3 1/2 inch diskette drive.                                                                                                 

- Free port (Ethernet) is optionally onboard.  Additional PCI ports allow further                       

network cards.                                                                                                                  

- Serial interface for barcode, modem or ceiling laser.                                                             

- Parallel interface for printer.                                                                                            

- CD-ROM-drive for reading and writing of CD`s (no dust protection guarantee).                   

- USB connection at the operating panel.                                                                          

DXF-Postprocessor Basic for CAD-Systems                  

-       DXF-Postprocessor for the connection of 2D CAD-programs to WoodWOP.                   

-       Import of 2D DXF-files                                                                                        

-       Converting is carried out under fixed profiles (rules)                                            

-       Display of the geometry, layer and drawing elements.                                                         

-       Creation of the WoodWOP programs.                                                                 

Conditions for the DXF-file: The drawing elements have to be filed on the corresponding layers for differentiation of the processings.  The layer should include numeric values for the definition of the Z-axis.

-       Operating system Microsoft Windows 98/ME resp. Windows NT4/2000/XP                    

-       Alphanumeric layer definition                                                                                 

Barcode Software (Barcode Control)                            

The barcode control is prepared for connection to a barcode reader of Datalogic. Software to read a barcode via the serial interface.  The software allows for the following individual adaptation of the barcode information:

-       Program name.                                                                                                         

-       Place number.                                                                                                           

 -       Modus for two places at the same time, e.g. for alternating processing.                       

The barcode can additionally include up to four variables.  When using variables the new NC-program is automatically generated after scanning through the production list.                                                                   

Hand Terminal                                       

Software For Power Control System                                        

WoodWOP is a workshop orientated programming system (WOP) of the Homag Group.  A standardized data format allows the interchange between all CNC-machines of the Homag Group.                                                

Machine Data Recording (MDR)                          

Information about maintenance rates.                                                                               

Production List                                      

Creation of manufacturing processes in list form.  Active positions can be processed parallel or in series.  Definition of up to ten (10) variables for the variant processing.                                                                              

WoodWOP for PC                                 

Installation for an external PC, e.g. in the planning department.                                            

Provision Teleservice, Modem                             

Activation of teleservice capability of the machine.  Includes a modem and the free of charge use of teleservice features during the guarantee period. After the guarantee period a teleservice contract is necessary for further use of the teleservice.                                                                                                                                            

Off-Line Programming Training                           

Number of vertical drilling spindles                    2 x 32                                            

Vertical drilling spindle power                           2.7 kW/3.5 HP                               

Vertical drilling spindle speed                            1,500 to 7,500 rpm                                

X/Y-axis grooving saw power                             2.7 kW/3.5 HP                               

X/Y-axis saw rotation speed                               2,000 to 7,500 rpm                                

Saw blade diameter required                              125 mm/5”                                     

Router spindle power   (power constant from 9000 rpm to 18000 rpm)                       

2 x 6.0 kW; 8 HP                                                                                                             

Router spindle speed                                          1,200 to 24,000 rpm                        

ETP tool holders supplied                                  2                                                   

Collets for ETP tool holders                               2                                                   

Length of machine                                             7200 mm/23.6’                               

Width of machine                                              3170 mm/10.4’                               

Height of machine                                              2820 mm/111”                               

Max. panel thickness                                          80 mm/3.1”                                    

Machine weight                                                 6999 kg/ 15,432 lbs.                                 

Positioning speed                                                                                                    

    X-axis                                                           138 M/min                                     

    Y-axis                                                           80 M/min                                          

    Z-axis                                                           50 M/min                                      

    Z-axis (Pressure Plate)                                  27 M/min                                           


Utility Requirements                                    


Operating Voltage                                             3 Phase 208/480 volt, + / - 5%         

Frequency                                                         60 HZ                                                   

Amperage Service                                       

Rigger: Not Required
All Information including Photos and Videos are supplied by a 3rd party Source.
Please confirm all data before committing to a purchase.
*Subject to credit approval. Additional programs available.